1550 TerrainCut

Front Mower

  • 7-Iron™ PRO Side Discharge or Fastback™ Rear Discharge Deck
  • Diesel Engine
  • Compatible with select front blade, snow blower and broom attachments
View Brochure

Features

Diesel engine has high-quality features to minimise operating cost

Hood open for access to engineHood open for access to engine
3-cylinder, liquid-cooled diesel engine3-cylinder, liquid-cooled diesel engine

The 1500 Series TerrainCut™ Front Mowers are powered by liquid-cooled, 3-cylinder diesel engines.

These engines feature low levels of exhaust and emissions, reduced noise levels, and excellent fuel economy. They also meet the necessary Environmental Protection Agency (EPA) Tier 4 emissions requirements.

The 1570, 1575, 1580, and 1585 models are biodiesel compatible from the factory up to B20. The 1550 model requires an optional kit to be compatible with B20 biodiesel fuel.

Engine drawing for 1570, 1575, 1580, and 1585Engine drawing for 1570, 1575, 1580, and 1585
 15501570, 1575, 1580, 1585
FuelDiesel (optional kit permits B20 compatibility)Diesel (B20 compatible)
Gross power at maximum rpm18.4 kW 25 hp27.5 kW (37.4 hp)
Displacement1.262 L (77 cu in.)1.642 L (100.2 cu in.)

Key features of the engine include:

  • Economical cast-in block cylinder design for good cooling and long life
  • Indirect fuel injection (1550)
  • Direct fuel injection (1570, 1575, 1580, 1585) 
    • Injects fuel directly on top of pistons for more efficient combustion
    • Delivers more horsepower per gallon of fuel
    • Improves starting
    • Develops more horsepower per gallon of fuel and improves starting
  • Aluminum alloy pistons with built-in steel struts are lightweight to reduce connection rod bearing loads and provide good heat transfer characteristics
  • Design permits tighter tolerances and neutralises expansion of the piston, thereby reducing blow-by gas and noise from the piston slap
  • Higher top rings on the piston and a thinner head gasket greatly reduce the volume of unburned waste gases and increase combustion efficiency
  • Timing gears and injector drive gears utilise helical profile gears to help lower engine noise; gear teeth have a newly designed roll-off profile, giving almost no clash, no noise, and no backlash
  • Fuel filter with replaceable element
  • Full-pressure intake manifold provides quick starts in temperatures down to 0°F (-18°C) (optional engine coolant heater attachment assists starting under more extreme conditions)
  • Auto-bleed fuel system – there is no need to prime the system if the tractor runs out of fuel; the system self-primes the injection pump, lines, and injectors, providing fast fuel recovery
  • Key start and shutoff eliminates fuel shut-off knob; electric solenoid shuts fuel supply off immediately when key is turned off
  • See-through coolant recovery tank permits operator to check coolant level without removing radiator cap
  • Enclosed engine compartment to keep out debris and lower sound levels
  • Sealed radiator compartment to keep trash and debris on outside of hood
  • Excellent torque for plenty of lugging power when operating in tough mowing conditions
  • Full-pressure lubrication for positive lubrication, even when operating on slopes
  • Dual-element, dry-type, replaceable air cleaner completely sealed for effective cleaning
    • 90 percent to 95 percent of dirt ejected before it reaches the paper element
  • Secondary safety element for additional filtering
  • Progressive-type air restriction indicator to let operator know when the filter needs servicing
  • Automotive-type alternator for plenty of charge to the battery and power for accessories 
    • 75 amp for open-station models
    • 95 amp for ComfortCab models
  • Automatic initiation of air heater for easier cold-weather starting
  • Automotive-sensing system tells operator when engine is ready to start
Rear-mounted radiators
Rear-mounted radiators (1550, 1570, 1580)Rear-mounted radiators (1550, 1570, 1580)
Rear-mounted radiators and air conditioner condenser (1575, 1585)Rear-mounted radiators and air conditioner condenser (1575, 1585)
Fuel tank is large capacity with convenient gauge for maximum uptime
Fuel tankFuel tank
Fuel gauge (shown on 1585)Fuel gauge (shown on 1585)

Fuel tank features:

  • 60.6 L (16-U.S. gal) capacity provides a 10-hour run time.
  • Top draw provides clean fuel.
  • Fuel indicator is conveniently located.

Mower decks for TerrainCut™ Front Mowers match a wide variety of needs

Since 1998 the John Deere 7-Iron™ mower deck has demonstrated commercial quality, performance, and durability. The 7-Iron PRO, FastBack™, and FastBack PRO mower decks deliver an even higher-quality cut in even more diverse conditions.

1580 TerrainCut Front Mower with 183 cm (72 in.) FastBack PRO Mower Deck1580 TerrainCut Front Mower with 183 cm (72 in.) FastBack PRO Mower Deck
1575 TerrainCut Front Mower with 183 cm (72 in.) 7-Iron PRO Mower Deck1575 TerrainCut Front Mower with 183 cm (72 in.) 7-Iron PRO Mower Deck

TerrainCut Front Mower Compatibility

 

Mower Deck 15501570157515801585
152-cm (60-in.) 7-Iron PRO Side-Discharge Mower DeckXXX*X*X*
157-cm (62-in.) FastBack Rear-Discharge Mower DeckXXXXX
183-cm (72-in.) 7-Iron PRO Side-Discharge Mower DeckXXXXX
183-cm (72-in.) FastBack PRO Rear-Discharge Mower DeckXXXXX

Rear weights (UC13263) are required based on machine configuration. Must also order TCB10303, rear weight mounting bracket.

*Mower deck offset for trimming capability. Vehicle track width is 5.1 cm (2 in.) wider on the discharge side of deck. This may cause the tyre to drive over uncut grass on discharge side of deck.


NOTE: These mower decks will not retrofit to F900 Series or F1145 Front Mowers.

Rotate for Service (RFS™)
Mower deck showing RFS featureMower deck showing RFS feature

Rotate for Service (RFS) feature provides access for cleaning and maintenance of the mower decks:

  • The rotation angle will vary depending on deck size and power unit tyre size.
  • No tools are required to access belts.
  • The underside of the mower deck is easy to access.
  • Easy on/off design simplifies installing and removing mower decks.
  • Top, greaseable spindles can be accessed without removing belt covers.

The Rotate for Service position also reduces the length of the machine for trailering.

Certification

TerrainCut Front Mowers comply with ANSI B71.4 safety certification.

Heavy-duty blade spindles
Cast-iron spindle housingCast-iron spindle housing
Cast-iron spindle housingCast-iron spindle housing

The mower spindle housings are made of ductile cast iron.


Key benefits of ductile cast-iron spindle housings:

  • Ductile cast-iron material provides superior impact strength.
  • Gusseted design puts reinforcement where it is needed.
  • Strength of cast iron protects against damage from blade impacts.
  • Grease fitting is mounted at the top for easy access.
  • Grease pressure-relief valve minimises seal damage from overfilling with grease and keeps debris from entering housing.
  • The 20.3 cm (8 in.) diameter housing distributes loads and impacts to minimise deck-shell damage.
  • Spindle allows ability to be rebuilt.

NOTE: The 183-cm (72 in.) 7-Iron V-Flex Side-Discharge Mower Deck has an aluminum center spindle housing. The outside blades are driven by cast-iron gearboxes.

152 cm (60 in.) 7-Iron PRO Side-Discharge Mower Deck
60-in. 7-Iron PRO Mower Deck60-in. 7-Iron PRO Mower Deck
60-in. 7-Iron PRO Mower Deck60-in. 7-Iron PRO Mower Deck

Features include:

  • Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
  • Trim-edge bumper reduces damage to the mower deck and property.
  • Redesigned front baffle manages airflow and controls clippings better.
  • Blade spindle housings are made of ductile cast iron
    • Gusseted design puts reinforcement where it is needed.
  • Spindle pocket reinforcement gives even greater structural durability.
  • Adjustable anti-scalp wheels help smooth out the mowing job.
  • Standard semi-pneumatic caster tyres will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

  • The mower deck is stamped from 7-gauge, 4.6 mm (0.179 in.) steel to minimise the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup
    • Provides precision components and long deck life
    • Single piece of steel means no welds to break
    • Provides a smooth underside, without corners, reducing material buildup
  • 1.9 cm (0.75-in.) solid steel bar is welded to mower deck perimeter for added strength.
  • The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
  • A deep-deck design of 14-cm (5.5 in.) delivers excellent airflow so material can be processed quickly and efficiently.
  • 2.5-cm to 12.7-cm (1-in. to 6-in.) cutting heights, in 1.3 cm (0.5-in.) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

  • Baffling system eliminates clumping, blowout, and windrowing.
  • Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.
157 cm (62 in.) FastBack Mower Deck
62-in. FastBack Mower Deck62-in. FastBack Mower Deck

The 157-cm (62 in.) FastBack rear-discharge mower is ideally suited for:

  • Areas where people are present
    • Schools
    • Parks
    • Playgrounds
    • Traffic areas (city boulevards, roadsides, etc.)
  • Conditions and applications:
    •  Areas with long grass and weeds
    • Areas where customer is not as concerned about having a wide dispersal of grass (park areas, roadsides, etc.)
  • Government bids that specify a rear discharge mower. 

Key features of the 157 cm (62 in.) Rear-Discharge Mower Deck include:

  • Mower deck is constructed of 7-gauge, 4.6 mm (0.179 in.) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Deck is constructed with a  unique baffling system that reduces clumping and windrowing and produces a finished appearance that competitive rear-discharge mowers cannot match.
  • The belt-drive system has an easy-to-adjust tension device.
    • By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
  • For easy service and maintenance, the deck can be rotated into the vertical locked service position.
  • Deep-deck design increases airflow so more material can be processed.
  • Operator can trim with either side.
    • Dual side trimming increases operator productivity.
  • 2.5 cm to 15.2 cm (1 in. to 6 in.) cutting heights, in 1.3 cm (0.5 in.) increments, allow the operator to match all mowing conditions.
  • Gauge wheels, rollers, or side-mounted skid shoes lift the deck over uneven surfaces for a well-groomed appearance.
  • Double-captured anti-scalp wheels provide increased durability.

  • Easy lift and lock system for service purposes.

  • Standard semi-pneumatic caster tyres will not go flat when punctured.

  • Spindles can be greased without removing belt shields.
  • 1-in. (2.5-cm) cold-forged spindles are strong for long life.
    • Heat-treated to provide additional strength
  • Certified to European (CE) standards
152-cm (72 in.) 7-Iron PRO Side-Discharge Mower Deck
72-in. 7-Iron Pro Side-Discharge Mower Deck72-in. 7-Iron Pro Side-Discharge Mower Deck

Features include:

  • Blade tip speed of 18,000 fpm (5486 m/min) for more blade strikes per inch mowed.
  • Trim-edge bumper reduces damage to the mower deck and property.
  • Redesigned front baffle manages airflow and controls clippings better.
  • Spindle pocket reinforcement gives even greater structural durability.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Adjustable anti-scalp wheels help smooth out the mowing job.
  • Standard semi-pneumatic caster tyres will not go flat from punctures.

The mower is designed to provide exceptional cut quality at higher travel speeds:

  • The mower deck is stamped from 7-gague, 4.6 mm (0.179 in.) steel to minimize the number of welds and provide a smooth underside, with fewer sharp corners, for reduced material buildup.
    • Provides precision components and long deck life
    • Single piece of steel means no welds to break
    • Provides a smooth underside, without corners, reducing material buildup
  • 1.9 cm (0.75 in.) solid steel bar is welded to mower deck perimeter for added strength.
  • The rounded corners of the stamped deck help distribute impact stress to reduce the potential of damage when the mower contacts trees, rocks, curbs, and other fixed obstacles.
  • A deep-deck design of 14 cm (5.5 in.) delivers excellent airflow so material can be processed quickly and efficiently.
  • 2.5-cm to 12.7-cm (1-in. to 6-in.)  cutting heights, in 1.3 cm (0.5 in.) increments, allow the operator to match all mowing conditions.

Unique baffling system allows grass to stand up before being cut, producing a uniform length and appearance:

  • Baffling system eliminates clumping, blowout, and windrowing.
  • Wide discharge opening provides even clipping dispersal for an excellent, finished appearance in all conditions.
183 cm (72 in.) FastBack PRO Mower Deck
72-in. FastBack PRO Mower Deck72-in. FastBack PRO Mower Deck

The 183 cm (72 in.) Rear-Discharge FastBack PRO Mower Deck is ideally for professional landscapers and government municipalities requiring rear discharge placement of grass and debris, John Deere FastBack PRO rear-discharge mower decks deliver a commercial mowing solution. Advantages of a rear- discharge mower include:

  • Less chance of damage from objects being thrown from the mower deck
  • Time savings with the ability to mow closely around fixed objects with either side of the deck
  • A cleaner mowing experience by lessening the amount of debris that can blow onto the operator

A rear-discharge mower deck is ideally suited for:

  • Schools
  • Parks
  • Playgrounds
  • Traffic areas (city boulevards, roadsides, etc.)
  • Areas with long, grassy spots that need to be cut, where you are not as concerned about wide dispersal of grass (park areas, roadsides, etc.)
  • Some government bids specify that the mower is equipped with a rear discharge.

Key features of the 183 cm (72-in.) Rear-Discharge Mower Deck include:

  • Mower deck is constructed of 7-gauge, 4.6 mm (0.179-in.) steel for the strength to stand up to the demanding use of commercial and municipal mowing applications.
  • Blade spindle housings are made of ductile cast iron.
    • Gusseted design puts reinforcement where it is needed.
  • Deck is constructed with a unique baffling system that reduces clumping and windrowing and produces a finished appearance that competitive rear-discharge mowers cannot match.
  • Operator can trim with either side.
    • Dual side trimming increases operator productivity.
    • Trim-edge bumpers on each side reduces damage to the mower deck and property.
  • The belt-drive system has an easy-to-adjust tension device.
    • By using a spring system, the risk for over tensioning is eliminated, ensuring a long belt life and excellent performance during the season.
  • For easy service and maintenance, the deck can be rotated into the vertical locked service position. Deep-deck design increases airflow so more material can be processed.
  • 2.5 cm to 15.2 cm (1 in. to 6 in.) cutting heights, in 1.3 cm (0.5 in.) increments, allow the operator to match all mowing conditions.
  • Gauge wheels or rollers lift the deck over uneven surfaces for a well-groomed appearance.
  • Double-captured anti-scalp wheels provide increased durability. Easy lift and lock system for service purposes.
  • Standard semi-pneumatic caster tyres will not go flat when punctured. Spindles can be greased without removing belt shields.
  • 2.5 cm (1 in.) cold-forged spindles are strong for long life.
    • Heat-treated to provide additional strength
  • Certified to European (CE) standards
Mower deck specifications

 

60-in. (152-cm) 7-

Iron PRO Side- Discharge

62-in. (157-cm)

FastBack Rear- Discharge

72-in. (183-cm) 7-

Iron PRO Side- Discharge

72-in. (183-cm)

FastBack PRO Rear- Discharge

Gauge (thickness)

7 gauge, 0.179 in. (4.6 mm)

7 gauge, 0.179 in.

(4.6 mm)

7 gauge, 0.179 in. (4.6 mm)

7 gauge, 0.179 in.

(4.6 mm)

Cutting height

2.5 to 15.2 cm (1 to 6 in.)

2.5 to 15.2 cm (1 to 6 in.)

2.5 to 15.2 cm (1 to 6 in.)

2.5 to 15.2 cm (1 to 6 in.)

Caster wheel type

Semi-pneumatic

Semi-pneumatic

Semi-pneumatic

Semi-pneumatic

Gauge wheels

Yes, front and rear

Yes, front and rear

Yes, front and rear

Yes, front and rear

Deck oscillation relative to ground plane

+/- 15 degrees

+/- 15 degrees

+/- 15 degrees

+/- 15 degrees

Lateral deck tilt

+/- 8 degrees

+/- 8 degrees

+/- 8 degrees

+/- 8 degrees

Deck installed at factory

No

No

No

No

Time required for one person to install or remove deck (without tools)

 

10 minutes

 

10 minutes

 

10 minutes

 

10 minutes

Time to change height of cut

3 minutes without tools

3 minutes without tools

3 minutes without tools

3 minutes without tools

Belt type

Kevlar belt

Kevlar belt

Kevlar belt

Kevlar belt

Belt shield type

Plastic

Plastic

Plastic

Plastic

Belt shield time to remove or install

2 minutes or less

2 minutes or less

2 minutes or less

2 minutes or less

Blade type

High lift

Medium lift

High lift

Medium lift

Blade tip speed

18,000 fpm (5,486

m/min)

16,000 fpm (4,877

m/min)

18,000 fpm (5,486

m/min)

18,000 fpm ( 5,486

m/min)

Spindles

3

3

3

3

 

Spindle-housing material

 

Ductile cast iron

 

Ductile cast iron

 

Ductile cast iron

 

Ductile cast iron

Deck level laterally when raised

Yes

Yes

Yes

Yes

Discharge

Side

Rear

Side

Rear

Mowing width

152 cm (60 in.)

157 cm (62 in.)

183 cm (72 in.)

183 cm (72 in.)

Overall width (chute down)

188 cm (74 in.)

163 cm (64 in.)

218 cm (86 in.)

188 cm (74 in.)

Weight

---

---

---

---

PTO shaft drive is easy to access for quick-change of equipment
Front mower PTO shaft driveFront mower PTO shaft drive

Live, independent power take-off (PTO) powers a mower deck, rotary broom, or two-stage snow blower:

  • PTO can be engaged or disengaged on the go for greater productivity.
  • Hydraulic PTO clutch has delay relief valve for soft engagement.
  • Wet clutch design provides long life.
  • PTO is easily accessible.
Tyres are matched to the machine size and mower widths
1550, 1570, 1575 tyres
TyresTyres

Standard drive tyres:

  • 23x10.5-12 or 23x8.5-12 (1550, 1570)
  • 23x10.5-12 (1575)

Available steering tyres: 18x8.5-10 (4WD) or 18x8.5-8 (2WD)

1580, 1585 tyres

Standard drive tyres: 26x12-12, 6 PR drive tyres (1580, 1585)

Standard steering tyres: 20x10.00-10, 6 PR steering tyres (1580, 1585)

Optional mulching kits add versatility to the mower decks
Typical mulch kit shownTypical mulch kit shown

Kits are available to convert the 60-in. (152-cm) and 72-in. (183-cm) 7-Iron™ PRO Side-Discharge Mower Decks into mulching decks for use in grass and leaves.

The mulch kits include mulching blades, baffles, end covers, and attaching hardware.

Easy-to-operate controls maximise productivity

1570 TerrainCut™ Front Mower1570 TerrainCut™ Front Mower
1585 TerrainCut Front Mower1585 TerrainCut Front Mower

Maneuverability:

  • Turn radius of 33 cm (13 in.)
  • Uncut circle of 71.1 cm (28 in.) with a 183 cm (72 in.) 7-Iron™ PRO mower deck
  • Deck offset and pulled rearward 
  • Tail-follows-the-trail trimming capability with 183 cm (72 in.) side-discharge mower deck
  • Steered wheels (tail) stay within the path (trail) cut by the mower deck, allowing maneuverability without the rear of the machine contacting mowing obstacles
Operator controls (1570 shown)Operator controls (1570 shown)
Master stop brake/directional foot pedalsMaster stop brake/directional foot pedals

Hydrostatic power steering provides the following benefits:

  • Makes it easy to turn the unit for less operator fatigue
  • Allows quick turns - two turns lock to lock - for excellent productivity

The steering console offers the following:

  • Throttle
  • Key switch
  • Headlight switch
  • T4 display for monitoring performance (1570, 1575, 1580, 1585)
Transmission controls, range lever, and on-demand four-wheel drive (4WD) lever (1585 shown)Transmission controls, range lever, and on-demand four-wheel drive (4WD) lever (1585 shown)
Controls including levers for double-spool auxiliary hydraulic kit (1585 shown)Controls including levers for double-spool auxiliary hydraulic kit (1585 shown)

Console information/warning lights include the following:

  • Hour meter
  • Battery discharge light
  • Engine oil pressure
  • Engine coolant temperature
  • Hydraulic oil over temperature
  • Air preheater
  • Lights
  • Power take-off (PTO) operation indication
Two-pedal foot controlTwo-pedal foot control

Two-pedal foot control:

  • Allows the operator to select speed and direction with just the touch of a toe
  • Keeps both hands free for steering and operating controls

 

Master stop brake (parking brake):

  • Provides stopping power to both drive wheels
  • Disengages the power take-off (PTO)
  • Disengages the optional cruise control
  • Used also for a parking brake
Individual turn-assist brakes and differential lockIndividual turn-assist brakes and differential lock

Individual turn-assist brakes:

  • Provides additional traction when operating on hillsides
  • Ideal for tight trimming situations
  • Works in conjunction with hydrostatic foot controls to stop or slow the unit for turns

Differential lock:

  • Locks both front drive wheels together for added traction
  • Easily engaged with the left foot
4WD lever (1570 shown)4WD lever (1570 shown)
Deck lift-control leverDeck lift-control lever

The 4WD control lever is standard on 1575, 1580, and 1585; it is a factory-installed option on the 1550 and 1570.

The 4WD control lever:

  • Allows the operator to select between on-demand or full-time 4WD on 1550, 1570, and 1575 models
  • Allows the operator to select between on-demand or full-time 4WD and full-time two-wheel drive (2WD) on 1580 and 1585 models

Electronic cruise control (optional):

  • Beneficial when mowing open areas or when transporting

The lift-control lever is conveniently located within easy reach of the operator's right hand.

1585 shown with control levers for double-spool auxiliary hydraulic kit1585 shown with control levers for double-spool auxiliary hydraulic kit

A two-speed transaxle shift lever is standard on 1580 and 1585.

Tilt steering
Tilt steering column (1550 shown)Tilt steering column (1550 shown)

Tilt steering column allows the operator to adjust to the most comfortable position:

  • Allows additional clearance for platform entry and exit
  • Over 15 in. (38.1 cm) of travel
  • Works in conjunction with the seat to accommodate all operators, regardless of size
Safety starting system helps protect the operator and others
1550 mowing grass1550 mowing grass

TerrainCut™ Front Mowers have an operator-presence system.

To start the engine the following conditions must be met:

  • Master brake must be depressed or the parking brake locked; the hydrostatic foot controls will then be in the neutral position.
  • PTO must be disengaged
  • Ignition key must be used.

In addition, once the engine is running, an interlock automatically shuts the engine and PTO off if the operator leaves the seat. To keep the engine running, the operator must disengage the PTO and set the parking brake before dismounting.

Tilt steering and headlights are standard equipment
Three-piece steering columnThree-piece steering column

The three-piece steering column provides the following:

  • Easy access to the steering valve and electrical components
  • Better fit-up and appearance
  • Easy adjustment to accommodate all operators
  • Standard 50-W halogen headlights
Brakes and differential lock are convenient to use for maximum productivity
Wet-disk brakes/differential lockWet-disk brakes/differential lock

Wet-disk brakes are standard equipment:

  • Provide positive stopping power and long life
  • Require minimal adjustment
  • Individual turn brakes are located on left side of platform

The differential lock is also included as standard equipment:

  • Locks both front drive wheels together for extra traction, when needed
  • Conveniently located pedal to allow the operator to engage the differential lock with the left foot while maintaining speed and direction (forward or reverse) with the right foot
12-V power outlet is convenient to use
12-V power outlet12-V power outlet

The 12-V power outlet can be used to recharge radios and cell phones, popular tools used by commercial cutters.

The outlet is conveniently located under the front of the seat.

Certification ensures compliance with safety standards
Rollover protective structure (ROPS)Rollover protective structure (ROPS)

TerrainCut Front Mowers comply with ANSI B71.4 2004 safety certification specification.

The ROPS complies with the U.S. Occupational Safety and Health Administration (OSHA) 1928.51 standard for rollover protection.

Front mower seats have standard suspension with arm rests for added comfort and productivity

Standard comfort-adjust suspension seatStandard comfort-adjust suspension seat
Optional air-ride suspension seatOptional air-ride suspension seat

Operator comfort enhances productivity. TerrainCut™ Front Mowers include suspension seats with green accents and an embroidered John Deere logo. The comfort-adjust mechanical spring suspension seat is base equipment, and an air-ride suspension is an optional upgrade. The operator can adjust suspension by increasing or decreasing pressure for optimum comfort. Fore-aft adjustments accommodate both tall and short operators.

 

Both seats are 61 cm (24 in.) tall and include back-angle, lumbar, and arm rest adjustments. The eye-catching seats are constructed from two unique vinyl textures and sewn with decorative stitching. Retractable seat belts prevent belts from becoming tangled in the seat suspension and controls.

 

Other comfort features include:

  • Standard cup holder
  • Noise level meets North American and European standards

Manage your commercial mowing fleet using John Deere Operations Center™

TerrainCut™ Front and Wide-Area MowersTerrainCut™ Front and Wide-Area Mowers
Overview

A JDLink™ M Modem - 4G connects a commercial mower to the John Deere Operations Center, which enables you to manage your fleet more efficiently, increase productivity, and reduce labor costs. With a modem and Operations Center, you are always connected to the work in progress and can make timely adjustments to keep your fleet mowing.

JDLink M Modem - 4G
JDLink M Modem - 4G JDLink M Modem - 4G

A JDLink M Modem - 4G is standard equipment on model year 2024 and newer TerrainCut Front and Wide-Area Mowers. A modem can be field installed on:

  • Model year 2024 and newer Z700 ZTrak™ Mowers
  • Most model year 2024 and newer Z900 ZTrak Mowers
  • Model year 2024 and newer Q800 QuikTrak™ Mowers
  • Model year 2022-2023 TerrainCut Front Mowers
  • Model year 2023 TerrainCut Wide-Area Mowers

See compatibility section for serial number breaks and requirements.

John Deere Operations Center
John Deere Operations Center is available on PC, Apple iOS, and Android mobile appsJohn Deere Operations Center is available on PC, Apple iOS, and Android mobile apps

The John Deere Operations Center tracks your fleet and provides tools to analyze mower data. The connected features vary by mower model.

Models

Location

and

status

GPS

speed

Geofencing

and

curfews

Engine

hours

Maintenance

planner

Machine

Analyzer

Tool

Fuel

level

Fuel

consumption

Diagnostic

trouble

codes

Service

Advisor

Remote

Z700 ZTrak Mowers

X

X

X

Key

X

---

---

---

---

---

Gasoline-powered Z900 ZTrak Mowers

X

X

X

Key

X

---

---

---

---

---

Z994R ZTrak Mowers

X

X

X

Key

X

---

---

---

---

---

 E Series QuikTrak Mowers

X

X

X

Key

X

---

---

---

---

---

Q820M, Q850M, and Q850R QuikTrak Mowers

X

X

X

Sync

X

X

X

---

X

---

Q865R EFI QuikTrak Mowers

X

X

X

Sync

X

X

X

X

X

X

1550 TerrainCut Front Mowers

X

X

X

Key

X

---

---

---

---

---

1570, 1575, 1580, and 1585 TerrainCut Front Mowers

X

X

X

Sync

X

X

---

---

X

X

1600 TerrainCut Wide-Area Mowers

X

X

X

Sync

X

X

---

---

X

X

 

Location and status
Operations Center map displaying past locations of a mowerOperations Center map displaying past locations of a mower
Mobile view of Operations Center map showing GPS speed Mobile view of Operations Center map showing GPS speed

The JDLink M Modem - 4G regularly transmits the location and operational status of each mower in the fleet so you can monitor mowing progress on the Operations Center.

  • Location history-Display of map with current and past locations of each mower.
  • GPS Speed-Maps each mower’s current and past speeds, based on GPS location data, so you can target operator training. GPS speed is only viewable on Apple iOS and Android mobile apps.
  • Geofencing-Alerts when a mower enters or exits a prescribed area, for example if the mower has been stolen or an operator entered an area that should not be mowed.
  • Curfews-Alerts if the mower is operating outside prescribed times, for example residential areas with early-morning noise restrictions.
Engine hours

The modem regularly transmits the mower’s engine hours to inform maintenance planning and balance use.

  • Sync-The mower reports actual engine hours to the Operations Center.
  • Key-Engine hours are estimated by monitoring the key switch. Engine hours can be corrected in Operations Center.
Maintenance planner
Operations Center Maintenance PlannerOperations Center Maintenance Planner

Factory or custom maintenance plans can be established in Operations Center. Maintenance alerts are sent when engine hours reach maintenance intervals.

Machine Analyzer Tool
Operations Center Machine Analyzer ToolOperations Center Machine Analyzer Tool

On select products, the modem reports the time the mower spent transporting, idling, and working. The Operations Center’s Machine Analyzer tool reports usage data which allows you to analyze operator behavior, identify causes of low productivity, and initiate corrective actions.

Fuel level

On select products, the modem reports the fuel level. On these products, an analysis of fuel consumption is available in the Operations Center Machine Analyzer Tool. Measuring fuel consumption enables you to address causes of excessive fuel use.

Diagnostic trouble codes (DTCs)

On select products, the modem transmits the trouble codes generated by the mower’s control units to the Operations Center. Addressing DTCs can reduce downtime and repair costs. For example, a low-engine oil pressure DTC can indicate an engine is low on oil. Addressing the issue can prevent costly downtime and repairs.

Service Advisor Remote

On select products, John Deere dealers can perform remote diagnostics, software programming, and adjustments without the cost of a service call.

Compatibility

A JDLink M Modem - 4G is standard equipment on model year 2024 and newer (SN 110,001-) TerrainCut Front Mowers and model year 2024 and newer (SN 690,001-) TerrainCut Wide-Area Mowers.

 

A JDLink M Modem - 4G can be field installed on the commercial mowing products listed below. Field installation attachments simplify modem installation, and include brackets, mounting hardware, harness, and instructions. Field installation requires a JDLink M Modem - 4G to be ordered separately.

Model

Compatible model years

Installation attachment

Z700 ZTrak Mowers

2024 and newer (SN 080,001-)

BUC11759*

Gasoline-powered Z900 ZTrak Mowers

2024 and newer (SN 130,001-)

BUC11759*

Z994R ZTrak Mowers

2024 and newer (SN 070,001-)

BUC11759*

Z997R ZTrak Mowers

2021 and newer (SN 800,001-)

To be determined

QuikTrak Mowers

2024 and newer (SN 010,001-)

BUC11744*

R Series commercial walk-behind mowers

To be determined

To be determined

TerrainCut Front Mowers

2022-2023 (SN 080,001-110,000)

BUC11797*

1600 TerrainCut Wide-Area Mowers

2023 (SN 680,001-690,000)

BUC11797*

*Expected by early 2024

Serviceability is designed-in to reduce maintenance cost and increase uptime

Engine hood
Large screened area of engine hoodLarge screened area of engine hood
Hood latchHood latch

Engine hood includes large screened area:

  • Minimizes the amount of material that can get to the cooling radiators
  • Minimizes the need to clean the hood screens 

Hood latch keeps the hood securely in place, providing an optimum seal:

  • A single hood latch is located on top of the hood behind the seat.
Engine hood opens to the rearEngine hood opens to the rear
Designed-in service accessibilityDesigned-in service accessibility

Designed-in service accessibility helps ensure daily maintenance is completed to keep the machine operating at peak performance.

 

The hood opens rearward, exposing the following:

  • Engine
  • Oil and fuel filter
  • Hydraulic oil cooler
  • Radiator check/fill

The hood can be totally removed, if necessary. The seat flips forward for access to air filter, fuse bank, engine oil dipstick, and front of engine.

Condenser release knobCondenser release knob
Condenser tilted back to permit cleaningCondenser tilted back to permit cleaning

Easy-to-turn knobs are provided to release the air conditioning condenser (1575 and 1585 only) and fuel and hydraulic oil coolers so they can be tilted back to permit thorough cleaning between them and the engine coolant radiator.

Quick response (QR) codes link to owner information web pages
QR code label on control consoleQR code label on control console

To speed access to owner information web pages, a QR code is printed onto a product identification number (PIN) label located on the control console near the seat. The owner information web pages that include links to:

  • Safety and how-to videos
  • Operator’s manuals
  • Parts catalogues
  • Maintenance reminder sheets
  • Attachments
  • Warranty statements
Foot platform access panel
Removable foot platformRemovable foot platform

The panel on the foot platform can be removed for access to the transaxle, PTO shaft, and most linkages.

 

Easy-to-read daily service decal is located on the bottom of the foot platform panel:

  • Provides access to easily hook up driveshaft when changing implements
  • Makes it more likely service will be performed at the optimum time, thus ensuring the highest level of performance and uptime
Panel on foot platform removedPanel on foot platform removed
#

Removal of the foot platform gives convenient access to the driveshaft that powers the mower deck, snow blower and rotary broom:

  • Helps make changing from one front implement to another easier and more convenient

 Hydraulic hoses have reusable O-ring seal (ORS) fittings:

  • ORS fittings seal at a lower torque to prevent leaks.
  • Fittings can be removed from a damaged hose and installed on another hose.
  • Downtime and cost for repairs are reduced considerably.
Rotate For Service™ (RFS) feature shownRotate For Service™ (RFS) feature shown
RFS service lockout latchRFS service lockout latch

RFS feature provides access for cleaning and maintenance of the mower decks:

  • The service-latch pin allows mower deck to lock into position to ensure deck is held in position for cleaning or service.
  • The top-greaseable spindle grease fittings can be accessed without removing the belt covers. 
Trailering features are included to reduce the time and cost to move equipment

Trailering features are designed-in for convenience:

  • Designed-in trailer tie-downs are located at the front and rear of the machine.
  • 26-degree deck lift will clear the steepest trailer ramps for easy loading and unloading.
  • Rotate For Service™ (RFS) decks take up less room when transporting on trailers, allowing more room for other important equipment.
Remote battery posts
Remote battery postsRemote battery posts

Remote battery posts simplify jump starting. Both positive and negative posts are located  in front of the right rear steer tyre.

Welded frame structure is made of high-strength steel

High-strength, tubular steel frame High-strength, tubular steel frame

The revolutionary tubular, high-strength welded steel frame provides durability and allows major components to be located lower in the machine:

  • The design results in a lower center of gravity for better stability and traction on hillsides and slopes.
  • Rollover protective structures (ROPS) are integral members of the frame.
Durable design

Durability features of the frame include:

  • Heat-treated cast-iron axles with 3.15 cm (1.24-in.) kingpins
  • Internal wet-disk brakes
  • Hydraulic PTO clutch, with brake
    • Provides smooth engagement and long life
  • Hydrostatic oil cooler
  • O-ring seal (ORS) hydraulic fittings
  • Integrated, shaft-driven power take-off (PTO)
  • Sealed relays and electrical connectors
  • Heavy-duty, dual hydraulic cylinders
  • Nodular cast-iron lift arm sockets
  • Cast-iron rear bumper

Hydrostatic transmission and transaxle are heavy-duty to maximise uptime

Kanzaki 30-cc transmissionKanzaki 30-cc transmission

A Kanzaki® 30-cc transmission is used for reliable operation.

 

Durability features include the following:

  • High-capacity hydrostatic transmission and heavy-duty transaxle maximize performance and uptime and minimize cost of maintenance. 
  • Charge pump is used to efficiently deliver oil to the transmission.
  • Oil cooler helps maintain optimum transmission oil temperature for superior performance and longer transmission life in the most challenging operating conditions.
  • Maximum forward top speed is 19.3 km/h (12 mph) on the 1550, 1570, and 1575 and 24.1 km/h (15 mph) on the 1580 and 1585.
  • Self-bleeding design helps keep air out of the system.

Kanzaki is a trademark of Kanzaki Kokyukoki Manufacturing Company.

Two-function mechanical rear-wheel drive for optimum use of the four-wheel drive feature

Mechanical rear-wheel drive axleMechanical rear-wheel drive axle

Mechanical rear-wheel drive is available as standard equipment (1575, 1580, 1585) or as a factory-installed option (1550, 1570):

  • On-demand four-wheel drive automatically engages and disengages as needed.
    • Constantly maximizes trimming ability
    • Offers better fuel economy than full-time four-wheel drive 
    • Provides better steering tyre wear than full-time four-wheel drive 
    • Increases traction and trimming ability to allow a novice operator to mow like an expert
    • Works in the forward direction only
  • Full-time four-wheel drive is on at all times.
    • Can be engaged or disengaged on the go
    • Provides maximum traction and flotation in poor conditions
    • Works in reverse as well as the forward direction
  • Two-wheel drive position is available on 1580 and 1585 with two-speed transaxle.
    • Disengages rear axle when transporting at high ground speeds

Dual drive tyres are available to optimise performance in challenging conditions (1550 and 1570 only)

Dual drive tyresDual drive tyres

Dual 23x8.5-12 drive tyres are available for increased hillside stability, flotation, and reduced ground compaction.

 

In addition, single drive tyres may be set in the narrow or wide position to match mowing conditions.

 

NOTE: These tyres are available for the 1550 and 1570 models only.

Tail-follows-the-trail design helps avoid obstacles in turns

Tail follows the trail
1585 TerrainCut™ Front Mower1585 TerrainCut™ Front Mower

Tail-follows-the-trail trimming with 183 cm (72 in.) mower decks. Steered wheels (tail) stay within the path (trail) cut by the mower deck, allowing maneuverability without the rear of the machine contacting mowing obstacles.

 

Maneuverability:

  • Turn radius 33 cm (13 in.)
  • Uncut circle –71 cm (28 in.) with a 183 cm (72 in.) 7-Iron PRO mower deck
    • Deck offset for increased trim capability

Front mower ballast requirements

Front mowers must be properly ballasted for both good performance and safe operation. Ballast requirements differ depending on the front mower model and the implement being used.

The chart below gives the minimum ballast requirements for the various product configurations. Additional ballast is recommended for operating on slopes or other conditions that may warrant it.

NOTE: Use only implements and accessories recommended by the manufacturer.

Front mowers and current (model year 2015 and later) implements

TerrainCut™ 1500 Series Front Mowers

 

 

Product Configuration

60-in. (152-

cm) Side-

Discharge Deck (7- Iron™ PRO)

72-in. (183-

cm) Side-

Discharge Deck (7- Iron PRO)

62-in. (157-

cm) Rear-

Discharge Mower Deck

72-in. (183-

cm) Rear-

Discharge Mower Deck

 

60-in. (152-

cm) HD Front Blade

 

47-in. (119-

cm) HD Two-Stage Snow Blower

 

60-in. (152-

cm) HD Two-Stage Snow Blower

 

60-in. (152-

cm) Rotary Broom

 

43-in. (109-

cm) Drop Spreader (Order Zone)

1550 Front Mower 2WD

1*

2*

1*

2*

0

2*

3*

1*

NA***

1550 Front Mower 4WD

0

1*

0

1*

0

2*

2*

0

Wide track

1570 Front Mower 2WD

1*

2*

1*

2*

0

2*

3*

1*

NA***

1570 Front Mower 4WD

0

1*

0

1*

0

2*

2*

0

Wide track

 

 

 

 

1575 Front Mower

 

 

 

 

Narrow track

+ 4 *

 

 

 

 

Wide track + 5*

 

Narrow track

+ 1 wheel weight on each side**

+ 3

weights* or wide track

+ 3 weights*

 

 

 

 

Wide track + 6*

 

 

 

 

1*

 

 

 

 

NA***

 

 

 

 

6*

 

 

 

Wide track + 1 wheel weight on each side**

+ 3 weights*

With 60-in. Rotary Broom: wide track + 2 wheel weight on each side**

or with 60-in.

Snow Blower: wide track

1580 Front Mower

0

1*

0

1*

0

NA***

2*

0

Wide track

 

 

 

 

1585 Front Mower

 

 

 

 

Narrow track

+ 4*

 

 

 

 

Wide track + 5*

 

Narrow track

+ 1 wheel weight on each side**

+ 3

weights* or wide track

+ 3 weights*

 

 

 

 

Wide track + 6*

 

 

 

 

1*

 

 

 

 

NA***

 

 

 

 

6*

 

 

 

Wide track + 1 wheel weight on each side**

+ 3 weights*

With 60-in. Rotary Broom: wide track + 2 wheel weight on each side**

or with 60-in.

Snow Blower: wide track

1400 and 1500 Series II Front Mowers

1420 Series II Front Mower

0

2*

1*

4*

6*

4*

6*

6*

NA***

1435 Series II Front Mower

0

2*

1*

4*

6*

4*

6*

6*

NA***

1445 Series II Front Mower

0

2*

1*

4*

6*

4*

6*

6*

NA***

1545 Series II Front Mower

0

2*

1*

4*

6*

NA***

6*

6*

NA***

1565 Series II Front Mower

0

2*

1*

4*

6*

NA***

6*

6*

NA***

1575/1585 Cab models: Rim design allows for tyre assembly to be mounted in two different configurations, a narrow track or wide track width to meet ballast requirements.

*42-lb (19-kg) (UC13263) Quik-Tatch weight (installation requires TCB10303, rear weight mounting kit).

**50-lb (23-kg) front wheel weight(s) required (installation requires BM18101, mounting hardware kit).

***NA - Not recommended for use on front mower.

NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements.

Front mowers and model year 2014 and prior implements

1400 and 1500 Series II Front Mowers

 

 

Product Configuration

60-in. (152-

cm) Side- Discharge Deck (7- Iron™ and 7-Iron II)

72-in. (183-

cm) Side- Discharge Deck (7-

Iron and 7- Iron II)

 

62-in. (157-

cm) Rear- Discharge Mower Deck

 

72-in. (183-

cm) Rear- Discharge Mower Deck

 

MCS 600

Hydraulic Dump

 

 

Soft cab

 

 

Hard cab

 

60-in. (152-cm)

HD Front Blade

47-in. (119-cm) HD

Two- Stage Snow Blower

60-in. (152-cm) HD

Two- Stage Snow Blower

 

60-in. (152-

cm) Rotary Broom

1420 Series II Front Mower

0

1*

0

1*

0

0

0

6*

4*

6*

6*

1435 Series II Front Mower

0

1*

0

1*

0

0

0

6*

4*

6*

6*

1445 Series II Front Mower

0

1*

0

1*

0

0

0

6*

4*

6*

6*

1545 Series II Front Mower

NA

1*

NA

1*

0

0

0

6*

NA

6*

6*

1565 Series II Front Mower

NA

1*

NA

1*

0

0

0

6*

NA

6*

6*

1500 TerrainCut Front Mowers

1550 Front Mower 2WD

1*

2*

1*

2*

NA

NA

NA

0

2*

3*

1*

1550 Front Mower 4WD

0

1*

0

1*

NA

NA

NA

0

2*

2*

0

1570 Front Mower 2WD

1*

2*

1*

2*

NA

NA

NA

0

2*

3*

1*

1570 Front Mower 4WD

0

1*

0

1*

NA

NA

NA

0

2*

2*

0

 

 

1575 Front Mower

 

 

Narrow track + 4*

 

 

Wide track

+ 5*

Narrow track 1 wheel weight on each side**

+ 3 weights* or wide track

+ 3 weights*

 

 

Wide track

+ 6*

 

 

NA

 

 

NA

 

 

NA

 

 

1*

 

 

NA

 

 

6*

 

Wide track 1 wheel weight on each side**

+ 3 weights*

1580 Front Mower

0

1*

0

1*

NA         NA

NA

0

NA

2*

0

 

 

1585 Front Mower

 

 

Narrow track + 4*

 

 

Wide track

+ 5*

Narrow track 1 wheel weight on each side**

+ 3 weights* or wide track

+ 3 weights*

 

 

Wide track

+ 6*

 

 

NA

 

 

NA

 

 

NA

 

 

1*

 

 

NA

 

 

6*

 

Wide track 1 wheel weight on each side**

+ 3 weights*

1575/1585 Cab models: Rim design allows for tyre assembly to be mounted in two different configurations, a narrow track or wide track width, to meet ballast requirements.

* 42-lb (19-kg) (UC13263) Quik-Tatch weight (requires TCB10303, rear weight mounting kit).

** 50-lb (23-kg) front wheel weight(s) required (installation requires BM18101, mounting hardware kit).

NA - Not recommended for use on front mower.

NOTE: Ballast requirements may change. Always refer to the implement owner's manual for the appropriate ballast requirements.

Roll-Gard™ rollover protective structures protects operators of open-station mowers

ROPS (upright position)ROPS (upright position)
ROPS (folded position)ROPS (folded position)

The foldable two-post Roll-Gard rollover protective structure (ROPS) and retractable seat belt are standard equipment.

  • Foldable for trimming, such as when mowing under trees or bushes